全文获取类型
收费全文 | 1798篇 |
免费 | 96篇 |
专业分类
公路运输 | 484篇 |
综合类 | 441篇 |
水路运输 | 604篇 |
铁路运输 | 305篇 |
综合运输 | 60篇 |
出版年
2024年 | 6篇 |
2023年 | 26篇 |
2022年 | 46篇 |
2021年 | 60篇 |
2020年 | 78篇 |
2019年 | 59篇 |
2018年 | 28篇 |
2017年 | 69篇 |
2016年 | 73篇 |
2015年 | 76篇 |
2014年 | 126篇 |
2013年 | 114篇 |
2012年 | 164篇 |
2011年 | 195篇 |
2010年 | 86篇 |
2009年 | 104篇 |
2008年 | 108篇 |
2007年 | 142篇 |
2006年 | 86篇 |
2005年 | 77篇 |
2004年 | 37篇 |
2003年 | 23篇 |
2002年 | 14篇 |
2001年 | 14篇 |
2000年 | 10篇 |
1999年 | 17篇 |
1998年 | 7篇 |
1997年 | 9篇 |
1996年 | 7篇 |
1995年 | 1篇 |
1994年 | 4篇 |
1993年 | 5篇 |
1992年 | 5篇 |
1991年 | 3篇 |
1990年 | 6篇 |
1989年 | 5篇 |
1988年 | 3篇 |
1987年 | 1篇 |
排序方式: 共有1894条查询结果,搜索用时 125 毫秒
41.
随着大型柴油发动机经济性和排放要求的不断提升,以及对发动机稳态、瞬态特性要求的不断提高,传统的涡轮增压系统已无法满足船用发动机全工况性能的要求。为了提高产品竞争力和适配性,针对某8缸直列船用柴油发动机开发了带有定压排气管的相继增压系统,并进行了发动机台架试验研究。结果表明:发动机中、低转速时,相继增压系统使发动机比油耗可以下降5%-10%,排气温度降低30%-45%,烟度下降55%-60%;最大扭矩可以提升15.1%-36.4%;发动机最大扭矩转速工况突加突卸响应性提升约28%-29%;相继增压系统中定压排气管的设计使得发动机高工况性能也有所提升,从而实现发动机全工况性能的提升。 相似文献
42.
Environmental contours are often applied in probabilistic structural reliability analysis to identify extreme environmental conditions that may give rise to extreme loads and responses. They facilitate approximate long term analysis of critical structural responses in situations where computationally heavy and time-consuming response calculations makes full long-term analysis infeasible. The environmental contour method identifies extreme environmental conditions that are expected to give rise to extreme structural response of marine structures. The extreme responses can then be estimated by performing response calculations for environmental conditions along the contours.Response-based analysis is an alternative, where extreme value analysis is performed on the actual response rather than on the environmental conditions. For complex structures, this is often not practical due to computationally heavy response calculations. However, by establishing statistical emulators of the response, using machine learning techniques, one may obtain long time-series of the structural response and use this to estimate extreme responses.In this paper, various contour methods will be compared to response-based estimation of extreme vertical bending moment for a tanker. A response emulator based on Gaussian processes regression with adaptive sampling has been established based on response calculations from a hydrodynamic model. Long time-series of sea-state parameters such as significant wave height and wave period are used to construct N-year environmental contours and the extreme N-year response is estimated from numerical calculations for identified sea states. At the same time, the response emulator is applied on the time series to provide long time-series of structural response, in this case vertical bending moment of a tanker. Extreme value analysis is then performed directly on the responses to estimate the N-year extreme response. The results from either method will then be compared, and it is possible to evaluate the accuracy of the environmental contour method in estimating the response. Moreover, different contour methods will be compared. 相似文献
43.
东海涌浪环境下大型起重船吊装组块耦合运动响应数值模拟研究 总被引:1,自引:0,他引:1
我国东海海洋环境复杂,经常出现小波高、长周期的涌浪.长周期涌对系泊大型起重船吊装海洋平台上部组块影响比较大,尽管涌的波高较小,但是,吊物组块运动幅度明显比同等波高海况时的要大,严重影响了海洋平台的安装施工效率和进度,甚至威胁作业安全.本文采用水动力势流软件,建立系泊-大型起重船(包括吊臂)-索具-大型组块吊物的耦合运动模型,研究复杂涌浪环境下耦合系统运动响应特性及其机理,并开展了参数敏感性分析,讨论对耦合响应影响因素.最后,对东海涌浪情况下起重安装施工,提出了降低吊装组块运动响应的建议措施. 相似文献
44.
45.
文章运用半隐式特征线分裂算子有限元算法对串列布置的静止上游柱体和下游圆柱的尾激振动问题进行了数值模拟研究。数值结果表明:上游柱体结构的形状、尺寸比(d/D)和折减速度(Ur)三个参数对下游圆柱体结构的动力响应、运动轨迹与涡脱落模态有着显著的影响,且与单圆柱工况相比存在明显区别;随着尺寸比的增大,上/下游柱体结构之间的互扰作用会由流致效应逐渐转变为尾流效应,使得频率特性发生变化,并会导致下游圆柱体结构的振动响应增强;当d/D=0.5和1.0时,下游圆柱体结构的运动轨迹主要为“8”字形;当d/D=1.5时,除了“8”字形外,运动轨迹还会呈现双弯刀形、“双8”字形和不规则形状。通过对流体力系数与位移时程曲线及位移PSD曲线特性进行分析,揭示了其相互作用的内在机理。另外,下游圆柱体结构的尾流场特性也会随参数的变化而变化,其涡脱落模态主要为2S、P+S和2P三种。 相似文献
46.
对海上风机支撑结构进行动力响应分析,求出结构危险节点的载荷谱和功率谱密度函数,结合疲劳损伤模型和Dirlik概率模型,分别在时域和频域内对支撑结构进行疲劳寿命分析.由于时域法计算疲劳寿命需进行应力循环计数,这一过程需处理的数据庞大,耗时长.频域法省去应力循环计数,代之以概率密度函数,可相对准确、快速地计算结构的疲劳寿命.分析结果表明,采用Dirlik概率模型的频域分析法能较准确地反映海上风机支撑结构在随机载荷作用下的疲劳损伤情况,计算结果误差在可接受范围内. 相似文献
47.
以某磁浮轨道交通(40+80+228+228+80+40)m大跨钢箱梁斜拉桥为研究对象,采用有限元软件ANSYS和多体动力学软件UM分别建立桥梁和磁浮列车模型。基于车桥耦合振动方法,针对2列磁浮列车相向行驶并在主跨跨中交会的最不利情形,进行列车以不同速度通过桥梁时不同梁高下车桥系统的动力响应及磁浮大跨桥梁的竖向刚度限值研究。结果表明:磁浮列车的竖向动力响应随车速的增大而显著增大,时速从40 km增大到140 km时,列车竖向动力响应增幅达到120%以上;车体竖向加速度和Sperling指标不是桥梁结构刚度限值的控制因素;磁浮列车的悬浮间隙对梁体刚度变化较为敏感,随着梁体刚度逐步增大,悬浮间隙的波动变小,梁体挠跨比减小约25%,悬浮间隙波动减小幅度达35%,悬浮间隙可作为中低速磁浮大跨桥梁结构刚度限值的控制指标;梁体挠跨比1/3015可作为磁浮大跨桥梁的竖向刚度限值。 相似文献
48.
49.
利用ABAQUS有限元软件建立了含碎石化层的沥青加铺路面结构模型,研究土基、旧路基层与碎石化层模量以及碎石化层和加铺层厚度对含碎石化层沥青加铺层路面结构的力学响应的影响,确定碎石化模量的控制范围.结果表明,荷载作用中心点及附近一定区域,沥青加铺层层底受拉;沥青加铺层层底拉应力对土基模量、旧路基层模量、碎石化层厚度不敏感,但当碎石化层模量较小(接近300MPa)或加铺层厚(大于20cm)时层底拉应力均较大,在重载作用下更大.因此碎石化道路必须验算沥青层层底拉应力指标.为使沥青层层底拉应力峰值不至于过大甚至超过容许拉应力,使得受拉区域控制在一定范围以内,同时为降低加铺层竖向剪应力及土基顶面压应变,并达到防治反射裂缝的效果,碎石化层的模量宜控制在500~1000MPa. 相似文献
50.